Whether for music, communication, or notifications, audio is an important feature of many personal computer systems. In a new FreeBSD system, an audio card will need to be configured to process audio files and send them to the connected speakers.
Fortunately, setting up audio on FreeBSD is simple and straightforward. This guide will walk through setting up and configuring audio, connecting a pair of headphones (including pairing Bluetooth models), and testing the system’s sound, all in under 10 minutes!
1. Setting Up the Sound Card
FreeBSD supports a wide variety of sound cards, these are listed in the Hardware Compatability List for each FreeBSD release. The Hardware Notes will list supported audio devices and which FreeBSD driver it uses. Start by identifying which driver will be needed for your specific audio device.
The device driver will need to be loaded to use the sound card, this can be easily done with kldload(8). To load the intel-specific driver, for example:
# kldload snd_hda
The driver can be automatically loaded on boot by configuring /boot/loader.conf. Available sound modules are listed in the snd(1) manual page, these can be viewed by using:
# man -k snd
Once the sound module has been checked, add a line to /boot/loader.conf to automatically load the driver. The line for the previous Intel driver would be:
snd_hda_load="YES"
To simplify identifying and loading a driver, the snd_driver module, a meta driver that loads all of the common sound drivers, can also be loaded:
snd_driver_load="YES"
2. Setting up Bluetooth
If the audio output require a Bluetooth connection, further configurations will have to be made to ensure Bluetooth support is loaded and configured. This section can be skipped if Bluetooth is not needed.
2.1 Loading Bluetooth Support
Before attaching a Bluetooth device, determine which Bluetooth driver it uses. A broad variety of Bluetooth USB dongles are supported by ng_ubt(4). Broadcom BCM2033 based Bluetooth devices are supported by the ubtbcmfw(4) and ng_ubt(4) drivers. Serial and UART based Bluetooth devices are supported by ng_h4(4) and hcseriald(8). For example, if the device uses the ng_ubt(4) driver:
# kldload ng_ubt
If the Bluetooth device will be attached to the system during system startup, the system can be configured to load the module at boot by adding the driver to /boot/loader.conf:
ng_ubt_load="YES"
Once the driver is loaded, connect the Bluetooth device. If the driver load was successful, output similar to the following should appear on the console and in /var/log/messages:
ubt0: vendor 0x0a12 product 0x0001, rev 1.10/5.25, addr 2
ubt0: Interface 0 endpoints: interrupt=0x81, bulk-in=0x82, bulk-out=0x2
ubt0: Interface 1 (alt.config 5) endpoints: isoc-in=0x83, isoc-out=0x3,
wMaxPacketSize=49, nframes=6, buffer size=294
To start and stop Bluetooth, use the driver’s startup script:
# service bluetooth start ubt0
2.2 Finding Other Bluetooth Devices
FreeBSD uses hccontrol(8) to find and identify Bluetooth devices within RF proximity.
One of the most common tasks is discovery of Bluetooth devices within RF proximity. This operation is called inquiry. Inquiry and other HCI related operations are done using hccontrol(8). To display a list of devices that are in range use:
% hccontrol -n ubt0hci inquiry
Inquiry result, num_responses=1
Inquiry result #0
BD_ADDR: 00:80:37:29:19:a4
Page Scan Rep. Mode: 0x1
Page Scan Period Mode: 00
Page Scan Mode: 00
Class: 52:02:04
Clock offset: 0x78ef
Inquiry complete. Status: No error [00]
Note: only devices that are set to discoverable mode will be listed.
The BD_ADDR is the unique address of a Bluetooth device, similar to the MAC address of a network card. This address is needed for further communication with a device. To to obtain the human readable name that was assigned to the remote device:
% hccontrol -n ubt0hci remote_name_request 00:80:37:29:19:a4 BD_ADDR: 00:80:37:29:19:a4 Name: Example Bluetooth
The Bluetooth system provides a point-to-point connection between two Bluetooth units, or a point-to-multipoint connection which is shared among several Bluetooth devices. The following example shows how to create a connection to a remote device:
% hccontrol -n ubt0hci create_connection BT_ADDR
create_connection accepts BT_ADDR as well as host aliases in /etc/bluetooth/hosts.
The following example shows how to obtain the list of active baseband connections for the local device:
% hccontrol -n ubt0hci read_connection_list Remote BD_ADDR Handle Type Mode Role Encrypt Pending Queue State 00:80:37:29:19:a4 41 ACL 0 MAST NONE 0 0 OPEN
3. Graphics Card Sound Driver
Modern graphics cards often come with their own sound driver, which may not be used as the default device. To confirm, run dmesg and look for the pcm entries:
... pcm0: <HDA NVidia (Unknown) PCM #0 DisplayPort> at cad 0 nid 1 on hdac0 pcm1: <HDA NVidia (Unknown) PCM #0 DisplayPort> at cad 1 nid 1 on hdac0 pcm2: <HDA NVidia (Unknown) PCM #0 DisplayPort> at cad 2 nid 1 on hdac0 pcm3: <HDA NVidia (Unknown) PCM #0 DisplayPort> at cad 3 nid 1 on hdac0 hdac1: HDA Codec #2: Realtek ALC889 pcm4: <HDA Realtek ALC889 PCM #0 Analog> at cad 2 nid 1 on hdac1 pcm5: <HDA Realtek ALC889 PCM #1 Analog> at cad 2 nid 1 on hdac1 pcm6: <HDA Realtek ALC889 PCM #2 Digital> at cad 2 nid 1 on hdac1 pcm7: <HDA Realtek ALC889 PCM #3 Digital> at cad 2 nid 1 on hdac1 ...
In this example, the graphics card (NVidia) has been enumerated before the sound card (Realtek). This can be changed to use the sound card as the default device with:
# sysctl hw.snd.default_unit=n
where n is the number of the sound device to prioritize. In this example, it should be 4. Make this change permanent by adding the following line to /etc/sysctl.conf:
hw.snd.default_unit=4
4. Automatically Switching to Headphones
Some systems may struggle with switching between audio outputs, fortunately FreeBSD allows for these to be specified in device.hints, which can be configured for automatic switchover. To start, identify how your system is enumerating the outputs with:
# dmesg | grep pcm
pcm0: <Realtek ALC892 Analog> at nid 23 and 26 on hdaa0
pcm1: <Realtek ALC892 Right Analog Headphones> at nid 22 on hdaa0
...
Add the following line to /boot/device.hints using the highlighted values from your own system. These will likely be different than the example. In this example, colored text has been used to identify where in the original string the values originated.
hint.hdac.0.cad0.nid22.config="as=1 seq=15 device=Headphones" hint.hdac.0.cad0.nid26.config="as=2 seq=0 device=speakers"
5. Testing Sound
To confirm that the sound card has been detected and properly configured, run dmesg | grep pcm. This example is from a system with a built-in Conexant chipset:
pcm0: <NVIDIA (0x001c) (HDMI/DP 8ch)> at nid 5 on hdaa0 pcm1: <NVIDIA (0x001c) (HDMI/DP 8ch)> at nid 6 on hdaa0 pcm2: <Conexant CX20590 (Analog 2.0+HP/2.0)> at nid 31,25 and 35,27 on hdaa1
The status of the sound card may also be checked using this command:
# cat /dev/sndstat FreeBSD Audio Driver (newpcm: 64bit 2009061500/amd64) Installed devices: pcm0: <NVIDIA (0x001c) (HDMI/DP 8ch)> (play) pcm1: <NVIDIA (0x001c) (HDMI/DP 8ch)> (play) pcm2: <Conexant CX20590 (Analog 2.0+HP/2.0)> (play/rec) default
The output depends on which sound card has been detected, so the result may look different. However, if no pcm devices are listed, check if the correct driver was loaded in the first step.
Another quick way to test the card is to send data to /dev/dsp:
% cat filename > /dev/dsp
Any file can be used for this and will produce noise through the connected audio device.
This article originally appeared on the FreeBSD website and is reprinted here with permission.
Comments